Applied Measurements Ltd. - PRODUCT NEWS








'Bolt-On' Force Sensors for reliable retrofit weighing

Fitting a weighing system to an existing silo, hopper or tank using a conventional load cell system can be expensive, disruptive and sometimes even impossible. UK sensor experts Applied Measurements Ltd offer a solution to these problems by using a simple bolt-on load transducer.

This weighing approach is cost effective and quick to install, causes a minimum of production down time and is ideal as a retrofitted system. The BOSS bolt-on sensor is a well-proven robust product consisting of a strain-gauged element encased in a protective housing. It is simply bolted to a structural member of the silo and deflects under the changing weight conditions, to give a varying electrical output relative to the load.

Bob Davies, general manager at Applied Measurements comments "with more than 25 years experience of bolt-on sensors, we assess the suitability of this method of measurement for each individual enquiry, including an on-site survey if required. This ensures the feasibility of a successful installation at the outset and we will commit to the accuracy likely to be achievable". The very first consideration is the available stress for the sensor to measure and this is broadly dependent on the load applied and the design of the supporting structure it is mounted on.

Bolt-on systems are more than adequate for the majority of vessel weighing or level monitoring systems, where accuracy in the order of 1% - 2% is acceptable. The benefit of this system to any company with a need to weigh grain or other loose material is that unlike radar and ultrasonic systems (both of which present a cross-contamination risk as holes must be drilled for mounting of equipment), the bolt-on product doesn't come into contact with the product at any stage.

Additionally, accuracy of the other systems mentioned will depend on the material profile within the vessel. For example it may tend to clump, build up on one side or heap in the middle.

This can cause rat-holes to be created where the top surface remains intact, but material drains away beneath until the top surface collapses into it. This can cause false readings as there is an impression of there being more material than there is, potentially resulting in inventory errors.

In practice, the standard transducers are bolted to a suitable supporting member such as a leg, girder, channel or pipe. However in some applications custom profiled mounting blocks may be required to suit the profile of the supporting steelwork.

For a system to be viable the load to be measured should be between 3000psi and 10,000psi. The accuracy achieved depends on a number of factors, but most significantly the amount of available strain to be measured.

Each BOSS sensor has an average sensitivity of 1.7mV/V for 10,000PSI

As a general rule, sensors mounted internally will give the best results. With external systems there will often be a margin of error due to zero shift, which is a result of differential expansion due to solar radiation but even this can be nullified to an extent. The accuracy achieved will be very dependent on the positioning of the sensor on the steelwork.

Accuracy bands:
· 3,000 - 5,000 PSI gives +/- 2 to 3% or better
· 5,000 - 7,500 PSI gives +/- 1 to 2% or better
· 7,500 - 10,000 PSI gives +/- 1%

Typical application:
A 220T cement silo on a 6-leg pipe section frame, giving 6000PSI total available signal. Our customer required best accuracy for batching to supply ships and road tankers. As the available signal was good but not exceptional, we suggested 2 x BOSS bolt-on sensors per leg to minimise errors and maximise accuracy. The result is that the customer can batch to ships +/- 1Tonne in 100T and +/-0.5Tonne in 30T. To minimise the effect of temperature, each Bolt-on sensor is fully insulated after installation

Suitable instrumentation to accompany the bolt-on sensors includes: mains or battery-operated digital displays, local amplifiers allowing the signals to be monitored in a control room or a telemetry system for wireless monitoring via a remote hand-held receiver or a control room PC system.

For more information on the range of BOSS sensors and other load measurement products, please contact Applied Measurements on 0118 981 7339 or email info@appmeas.co.uk


About Applied Measurements Ltd
Applied Measurements Limited offers a comprehensive selection of transducers based on strain gauge technology. Our product range includes sensors to measure load, pressure, torque and displacement. In addition, a custom transducer design service and strain gauge bonding facilities are also available.
To support the transducer range, a variety of analogue and digital instrumentation is available including high resolution, high speed and RS232/485 equipped signal conditioners and indicators, as well as portable battery powered indicators with integral data-logging, enabling us to offer complete systems with calibration traceable to UKAS standards.
In addition to our comprehensive range of 'standard' transducers, we also have the capability to design, develop and manufacture custom devices to meet specific needs. Our expertise is based on bonded strain gauge technology, which is carried across our complete line of transducers. Our involvement in your project can be at any stage, from development and design, through prototypes, testing and into full production.

For more information, please contact :-

Applied Measurements Ltd.
Tel: +44(0)118 981 7339
Fax: +44(0)118 981 9121
Email:
info@appmeas.co.uk
Website: www.appmeas.co.uk

April 2010

 For other NEW PRODUCT information, click here...

Home - Website - Search - Suppliers - Links - New Products - Catalogues - Magazines
Problem Page - Applications - How they work - Tech Tips - Training - Events - Jobs