Micro-Epsilon UK Ltd. - PRODUCT NEWS






Factors to consider when selecting non-contact colour measurement sensors

There are several key factors that need to be considered before purchasing or specifying a non-contact colour sensor, including accuracy, the type of surface or object being measured, environmental conditions and mechanical set up, says Stephen Smith, Product Sales Engineer at Micro-Epsilon UK.

Accuracy
How accurate does the sensor need to be? Is it the absolute colour that you need to measure or just colour detection. For measuring absolute colour, the sensor accuracy (measured in Delta E) will need to be high, in the range 0 to 1.0 ?E. If you are unsure of the accuracy, speak to the sensor supplier for advice and guidance.

What object or material do you need to measure?
For non-contact colour sensors, the ideal surface in terms of sensor performance and accuracy is a flat, smooth one, where the same optics can be used. However, textured or structured surfaces can also be measured accurately by changing the measuring head on the sensor and/or the light source. In addition, multiple sensors can be used to measure at different measuring points on the sample and then averaging these values.

Curved surfaces or samples can also cause problems for colour sensors. On a curved surface, the light from the light source is reflected back to the receiver differently compared to a flat surface. If the sensor controller is not set up to deal with this, the accuracy of the sensor will suffer. For a sensor to perform accurately, the measurement opening has to be fully covered and, as a general rule, the curved radius of the sample should be less than 10 times the diameter of the measurement field.

Even transparent or translucent objects can be measured using a non-contact colour sensor.

Environmental conditions
In many production processes, the temperature will fluctuate. If the colour sensor becomes too hot, its accuracy may suffer, i.e. the Delta E value of the sensor will change as the temperature increases. Therefore, look for a supplier that states clearly on the sensor datasheet how the accuracy of the sensor changes with temperature.

Dirt, dust and oil will affect the accuracy of colour measurements. Non-contact colour sensors are more sensitive to contaminants in the measuring gap.

Mechanical set up
Mechanical mounting of the sensor and maintaining the distance between the sensor and the target object is important, particularly if the sensor is integrated to an inline production process. Vibrations from the surrounding environment may move the sensor and therefore affect its colour measurement accuracy.

Filters and lenses
In order to measure colours accurately, lenses are important. Clear glass lenses are used for large distances and matt surfaces, while sensors with diffuse lenses are used for inhomogeneous, textured and shiny surfaces. A polarizing filter is normally used for highly reflective surfaces. Sensors with UV LEDs tend to be used for fluorescent objects. Look for a supplier that can offer a range of different lenses across its sensor series.

Connectivity/networking
If colour measurements need to be made on high speed production lines, the inline colour measurement system will need to be integrated to other industrial control/quality control systems. The measurement system should therefore provide a range of connectivity/networking options including digital interfaces such as Ethernet, EtherCAT and RS422. These interfaces allow colour measurements to be monitored remotely.

Unlike conventional inline colour measurement systems, the latest advanced systems recognise colours not only by comparing them to reference values, but also by using the reflection spectrum to ensure unique identification.

Adaptive learning
Most suppliers will provide their colour sensors with a 'teach-in' function. This enables the sensor to learn and adapt to the application by using samples of the correct colour. Following this process, the sensors are able to compare the colour samples they have been taught with the target object, then operate independently, normally outputting a pass/fail signal.


About Micro-Epsilon
Micro-Epsilon (www.micro-epsilon.co.uk) is a major global manufacturer of sensors, headquartered in Germany. The company's range of displacement sensors measure everything from to distance, position, vibration, dimensions and thickness, using both contact and non-contact measurement techniques. These techniques include 1D, 2D and even 3D laser-optical sensors and systems, eddy-current, capacitive, LVDT & inductive, potentiometric and draw-wire principles. In addition, Micro Epsilon has developed its own range of non-contact infrared temperature sensors that can measure virtually any target temperature from -40 to +3,300°C. The company also manufactures a comprehensive range of colour recognition sensors.

With more than 45 years' experience in the industry, Micro-Epsilon isn't just a sensor manufacturer. The company is highly innovative and understands the importance of providing complete solutions and support services for its customers. The firm is renowned for its expertise in consulting, development and application of industrial sensors to complex, customer-specific solutions for measurement, inspection and automation. The focus is on selling technical advantage to its customers.


For sales and technical information contact:-

Chris Jones
Micro-Epsilon UK Ltd.
Telephone: +44(0)151 355 6070
Fax: +44(0)151 355 6075
Email:
info@micro-epsilon.co.uk
Website:
www.micro-epsilon.co.uk

March 2017

Home - Search - Suppliers - Links - New Products - Catalogues - Magazines
Problem Page - Applications - How they work - Tech Tips - Training - Events