Micro-Epsilon UK Ltd. - PRODUCT NEWS






First public run of BLOODHOUND SSC is a resounding success with the help of sensors from Micro-Epsilon UK

BLOODHOUND SSC reached a major milestone in October, as it made its first public run at the Aerohub in Newquay. However, the event wasn't just about driving the car successfully down the runway and showing it to spectators; it was also about testing the car and putting it through its paces, in particular, testing of hundreds of on-vehicle sensors that they were performing correctly under such extreme operating conditions.

As a Product Sponsor of the BLOODHOUND SSC Project, Micro-Epsilon UK has supplied a variety of high precision sensors and measurement systems for the BLOODHOUND SSC Project, which have been used throughout the testing and production stages.

Wheel spin tests at Rolls-Royce
In 2014, for example, Micro-Epsilon UK supplied a variety of non-contact laser displacement sensors and an infrared thermal imaging camera for use in high speed (up to 10,500rpm) wheel spin tests. The tests, which took place at Rolls-Royce's test facility in Derby, were carried out on the first of the BLOODHOUND machine's four solid aluminium wheels. The wheel spin test was the highest ever rpm recorded on the test rig.

The objective was to verify that the growth (expansion), temperature increase (due to air friction) and vibration of the wheel were within expected, safe limits and whether these test results would closely match the BLOODHOUND Team's own predictions using computer simulation and FEA software. For the tests, Micro-Epsilon UK supplied a total of 15 laser displacement sensors from its optoNCDT series, as well as a thermoIMAGER TIM 450 compact, high resolution infrared imaging camera.

The laser displacement sensors were set up on the test rig to measure the radial and axial run out of the aerospace-grade aluminium wheel as it rotated at speeds of up to 1,100mph (the wheels will travel at speeds up to 1,000mph during the supersonic machine's record breaking attempt). In addition, laser displacement sensors were also set up to measure the thermal expansion of the frame that runs across the top of the test rig (i.e. for test rig calibration purposes). Four optoNCDT 1402 laser sensors were mounted underneath the test rig in a confined space to measure the run out, alignment and any other movements of the test rig, including the steel hub that the wheel was mounted to.

Micro-Epsilon also supplied its thermoIMAGER TIM 450 infrared imaging camera for the wheel spin test. This compact, high resolution camera was located in a confined space underneath the test rig to monitor the temperature of the entire wheel during the spin test.

During the test, the wheel was successfully spun to 10,429 rpm (174 revolutions per second). Test results were similar to the predictions that the BLOODHOUND engineers had calculated using their computer simulation software. The expansion of the wheel's 902.6mm diameter by 1.6mm was as expected. So too was the "dishing" of the wheel caused by a variation in expansion rates between the aluminium material of the wheel and the steel hub. According to the BLOODHOUND Team, the empirical data collected during the test will now be used to fine-tune the computer simulations, delivering a more optimum wheel design.

Measuring vehicle ride height
In 2015, Micro-Epsilon UK also supplied non-contact laser displacement sensors for on-vehicle ride height tests. The tests were carried out at the Jaguar Land Rover Gaydon Centre in Warwickshire. Mounted to the chassis of a Jaguar XF test vehicle with the laser window pointing down towards the ground, the optoNCDT 1700 high speed sensor accurately measured and monitored the ride height of the car. The sensor has enabled the BLOODHOUND SSC team to adjust the suspension characteristics in order to optimise the performance of the car. For the ride height tests, two optoNCDT 1700 laser displacement sensors were mounted side-by-side to an adapted tow bar at the rear of the Jaguar XF. As well as on-vehicle testing, Micro-Epsilon's optoNCDT 1700 series of laser displacement sensors will also be used for the BLOODHOUND SSC record attempt itself.

For more information, please call the Micro-Epsilon sales department on 0151 355 6070 or email info@micro-epsilon.co.uk


About Micro-Epsilon
Micro-Epsilon (www.micro-epsilon.co.uk) is a major global manufacturer of sensors, headquartered in Germany. The company's range of displacement sensors measure everything from to distance, position, vibration, dimensions and thickness, using both contact and non-contact measurement techniques. These techniques include 1D, 2D and even 3D laser-optical sensors and systems, eddy-current, capacitive, LVDT & inductive, potentiometric and draw-wire principles. In addition, Micro Epsilon has developed its own range of non-contact infrared temperature sensors that can measure virtually any target temperature from -40 to +3,300°C. The company also manufactures a comprehensive range of colour recognition sensors.

With more than 45 years' experience in the industry, Micro-Epsilon isn't just a sensor manufacturer. The company is highly innovative and understands the importance of providing complete solutions and support services for its customers. The firm is renowned for its expertise in consulting, development and application of industrial sensors to complex, customer-specific solutions for measurement, inspection and automation. The focus is on selling technical advantage to its customers.


For sales and technical information contact:-

Chris Jones
Micro-Epsilon UK Ltd.
Telephone: +44(0)151 355 6070
Fax: +44(0)151 355 6075
Email:
info@micro-epsilon.co.uk
Website:
www.micro-epsilon.co.uk

November 2017

Home - Search - Suppliers - Links - New Products - Catalogues - Magazines
Problem Page - Applications - How they work - Tech Tips - Training - Events